Home › Services › Radiant Floor Heating in Fort Collins, CO

Radiant Floor Heating in Fort Collins, CO

Ask anyone who has it. There's no heat like a warm floor on a January morning. Radiant floor heating moves warm water through tubing in or under your floors. The floor itself becomes the radiator. The heat is even and silent. It rises exactly where you live. No vents. No drafts. No dust blowing around. No cold tile und

Hydronic radiant heating manifold with PEX tubing

We install hydronic radiant floor systems in new construction and major remodels across Fort Collins. Hydronic means heat carried by hot water. We do single-room additions. We do whole-house installs. We also service existing radiant systems.

Warm floors start here: call (970) 387-7504 to request a quote, or check availability online.

What One Job Looks Like

The bathroom floor zone. A remodel added a radiant zone under a new tile bathroom floor. The zone runs off a new high-efficiency boiler. Bare feet now hit warm tile on January mornings. Warm floors spoil you fast. Plain carpet starts to feel like a compromise. Turnaround: three days, timed with the remodel. Price range: $4,000–$7,500 for the boiler at the heart of the job. Scope: lay a new radiant zone under the tile floor and tie it to a new high-efficiency boiler. Materials: PEX tubing under the tile and a new boiler. Size: one bathroom zone.

How radiant floor heating works

Cross-linked polyethylene (PEX) tubing loops through the floor assembly. PEX is a flexible plastic pipe made for hot water. It can sit in a concrete slab. It can staple under a subfloor with heat transfer plates. It can set into a thin overpour on an existing slab. A boiler or water heater heats the water to a modest 100–140°F. That is far cooler than baseboard systems need. A manifold sends the water loop by loop. A manifold is a hub that splits water into each loop. Zone valves or pumps control the flow. Each zone gets its own thermostat.

The heat source is the entire floor surface. So the system runs at low water temps. That makes it very efficient. It pairs well with a condensing boiler or heat pump. Those units love low-temp operation.

New construction vs. retrofit

  • New builds and additions: This is the ideal case. Tubing goes in before the slab is poured or the subfloor goes down. It's simply part of construction. This is the most cost-effective way to get radiant. It's popular in the custom homes going up around Fort Collins.
  • Slab-on-grade retrofits: Tubing can set in a thin concrete overpour on top of the existing slab. You lose an inch or so of ceiling height. You need to manage transitions at doors. But it works.
  • Above-subfloor retrofits: Low-profile panel systems sit on top of the existing floor. They have tubing channels. Then the finished floor covers them. Higher material cost, minimal demolition.
  • Underfloor (staple-up): Tubing staples beneath the subfloor between joists. Aluminum transfer plates spread the heat. There is no floor height change. But output is lower. It is best for extra heat or mild zones. It is not best as primary heat in our climate.

We'll tell you honestly which approaches fit your project. Radiant is wonderful, but it's not the answer for every remodel. Sometimes mini-splits or baseboards make more sense, and we'll say so.

Zones, controls, and floor coverings

Radiant zones by nature. The manifold makes it easy to give each area its own thermostat. The master suite gets one. The great room gets one. The basement gets one too. Bathrooms get their own small zone so the tile is always warm. Controls range from simple thermostats to smart systems. Floor sensors cap the surface temp.

Floor covering matters. Tile and stone conduct heat beautifully. They are the ideal pairing. Conduct means they pass heat through fast. Engineered wood works with temp limits. Carpet insulates against the heat. Thick carpet and pad can cut output a lot. So we plan around your flooring choices before tubing goes in.

The heat source

Radiant needs warm water from something. It can be a boiler, the classic pairing. See Boiler Services. It can be a high-efficiency water heater for smaller systems. Or it can be an air-to-water heat pump for the efficiency-minded. Condensing boilers are the sweet spot. Radiant's low water temps let a condensing boiler stay in its most efficient mode almost constantly. Baseboard systems can't do that.

Service for existing radiant systems

Already have radiant? We service it. We diagnose manifolds and zone valves. We replace circulator pumps. A circulator is the pump that moves the water. We remove trapped air. Gurgling zones mean trapped air. We upgrade controls. We do boiler-side service. Uneven heating across zones usually traces to flow balance or a stuck valve. Both are fixable.

What affects the cost of radiant floor heating

  • Project type: New construction is the most economical. Retrofits cost more per square foot.
  • Square footage and zone count: More area and more zones mean more tubing. They mean more manifold capacity and controls.
  • Floor assembly: Slab embed vs. overpour vs. panel system vs. staple-up.
  • Heat source: New boiler vs. existing equipment vs. heat pump.
  • Controls: Basic thermostats vs. smart zoning with floor sensors.

Related services: Boiler Services, Mini-Split Systems, Smart Thermostats

Frequently Asked Questions

Can radiant floor heating be the only heat source in a Fort Collins home?
Yes. Properly designed, it handles our winters. The key is the heat-loss calculation. You need enough tubing. You need correct spacing. You need a heat source sized for design-day temps. Design-day means the coldest days the system is built for. It's done routinely in new Colorado builds. Retrofits need an honest look at the floor assembly's output capacity.
What flooring works best over radiant heat?
Tile and stone are ideal. They conduct heat fast and feel great. Engineered hardwood works with surface temp limits. Carpet is the worst pairing. Thick pad insulates against the heat you're paying for. Decide flooring before the tubing design, not after.
How long does radiant floor installation take?
In new construction, tubing installation takes days within the broader build schedule. Retrofit overpours and panel systems for a zone or two typically run a week. That includes cure and finish time. Whole-house retrofits are larger projects. We scope them individually.
Is radiant heating expensive to run?
No. It's among the most efficient ways to heat. Low water temps. No duct losses. Zone-by-zone control means you heat only what you're using. Operating costs typically beat forced air. That is especially true with a condensing boiler behind it.
Can you add radiant to just a bathroom or addition?
Absolutely. Single-zone retrofits are common. A bathroom floor zone can run off the existing boiler. Or a small electric mat can serve tiny areas. Hydronic is better for larger ones. It is one of the highest-satisfaction upgrades we install.
What maintenance does a radiant system need?
Very little on the floor side. There are no moving parts under the floor. The care is on the mechanical side. The boiler or heat source gets serviced once a year. Circulators get checked. Manifold valves get exercised. The system gets checked for air. Add it to your boiler's annual visit.

Call (970) 387-7504 for radiant floor heating in Fort Collins, CO. The most comfortable heat there is — done right from the tubing up.

Need Heating or Cooling Help?

Call (970) 387-7504 to request a quote or check availability. Or send the form. We will get back to you during business hours.

We serve Fort Collins and the surrounding northern Colorado communities. See our full service area.

Get a Fast Quote

Call Now (970) 387-7504Free Estimate