We find and seal duct leaks. We repair damaged runs. And we replace ductwork that's beyond saving. We work in attics, crawlspaces, and basements across Fort Collins and Larimer County.
Losing air to your attic? Call (970) 387-7504 to request a quote, or check availability online.
One Job, Start to Finish
The lost return. A crawlspace return duct had pulled loose years ago. The system had been heating the crawlspace ever since. The run got reconnected and sealed. Rooms warmed up. The furnace ran less to do it. Turnaround: one day. Price range: $500–$2,000. Scope: refit the loose crawlspace return and seal the run. Materials: duct seal and refit duct parts. Size: one return run.
Signs your ductwork is the problem
Duct issues disguise themselves as gear problems. Before you blame the furnace, check for these:
- Some rooms are always too hot or too cold while others are fine.
- Weak airflow from some vents, strong from others.
- A dusty house no matter how often you clean.
- Energy bills climbing while the gear is fairly new.
- The system runs longer than it used to for the same result.
- Musty or attic-like smells when the system runs.
- Visible disconnected, crushed, or sagging ducts in the attic or crawlspace.
- Rooms that never quite get comfortable no matter the thermostat setting.
If your gear is under 10 years old but comfort is poor, the ducts are the prime suspect.
Repair vs. replacement: how we decide
Not every duct problem needs new ductwork. Here's our honest breakdown:
Repair and seal when:
- Leaks are at joints and connections. Register boots are a top failure point too. A register boot is the fitting where a duct meets a vent.
- Ductwork is otherwise intact and properly sized.
- A section is crushed or disconnected but the rest of the run is sound.
- Insulation is thin but the duct itself is fine. We can add wrap.
Replace when:
- Flexible duct is kinked, compressed, or chewed through in multiple places.
- The original ductwork is undersized for the system. No amount of sealing fixes wrong sizing.
- Old ductboard is delaminating or growing mold from past moisture. Ductboard is a rigid board made of compressed fibers.
- Layout is fundamentally bad. Long tortured runs with sharp bends strangle airflow.
We pressure-test and inspect before recommending either. Sealing good ducts costs far less than replacing them. And we'll never sell you replacement when sealing does the job.
How duct sealing and replacement work
- Inspection. We map your duct system. Attic, crawlspace, basement. We check every joint, run, and boot we can reach. We take photos so you see what we see.
- Your quote. Sealing is priced by the system. Replacement is priced per run. We explain material options.
- Sealing. We seal joints and connections with mastic. Mastic is the thick brush-on sealant that actually lasts. We do not use duct tape. It dries out and fails. We fasten loose connections with screws and straps.
- Replacement. Old runs come out. New R-8 insulated flex or rigid metal duct goes in. R-8 is the insulation rating. Higher numbers mean better heat resistance. We size it properly. We support it every few feet so it doesn't sag. We seal connections at every joint.
- Verification. We run the system. We measure airflow at the registers. You should feel the difference immediately. And we confirm it with readings.
Fort Collins duct realities
Our housing stock gives ducts a hard life. Attic installs bake every summer. Flex duct sags between supports. Insulation compresses. Connections pull apart from thermal cycling. Thermal cycling is the daily swing between hot and cold. Crawlspace ducts in older homes sit in dampness. They become rodent highways. New construction in the growth corridors sometimes has ducts installed fast rather than well. Sharp bends. Over-long runs. Boots never sealed to the drywall. And many homes still carry the original ductwork from a 1980s furnace. It now feeds a modern high-efficiency system it was never sized for.
What affects the cost of duct work
- Scope: Sealing a system vs. replacing every run is a different project entirely.
- Accessibility: An open basement is fast. A tight crawlspace is slower. A 140-degree attic is slower too.
- Material: Insulated flex vs. rigid sheet metal. Metal costs more and lasts longer.
- System size: More runs, more work.
- Combined projects: Pairing duct replacement with a furnace or AC install saves on labor. We're already in the mechanical spaces.
Related services: Air Duct Cleaning, Furnace Installation, AC Installation
Frequently Asked Questions
How much air do leaky ducts really waste?
Can you seal ducts without tearing open walls?
Is duct tape okay for sealing ducts?
How long does duct replacement take?
Will new ducts make my house quieter?
Should I replace ducts when I get a new furnace or AC?
Call (970) 387-7504 for duct repair and replacement in Fort Collins, CO. Fix the delivery, and the equipment finally gets to shine.
